Otomatisasi Pengering Padi Berbasis Arduino Uno
Main Article Content
Abstract
In general the drying of grain in Indonesia is still carried out in a relatively simple or traditional way of drying by heating it in the hot sun or drying it. This simple drying process generally takes three days for the drying process to approximately one week. Therefore it is necessary to make a dryer to reduce the time constraints. To overcome the problem in the drying process manually, in this study the authors will design an automatic dryer. Based on the test results, open the roof of the roof to the light above, when the light intensity is bright (morning or afternoon), the roof of the dryer opens. Whereas when the light intensity is dark (cloudy or night) the roof of the drying tub closes. When the roof is open it takes 00: 04.4 seconds while when closing it only takes 00: 01.2 seconds. The process of testing grain drying starts at 1:40 a.m. - 1:40 p.m. and the temperature results obtained at 10:40 p.m. are 50 ᵒC and when the temperature has reached the specified limit, the incandescent lamp dies and the fan inside the drying chamber rotates so that the rice stays dry and the temperature in the room is not moist.
Article Details
Section
How to Cite
References
. Adhim, Mochammad Machrus et al. 2005. “Spin Dry-Pad: Mesin Putar Pengering Padi Berbasis Sistem Otomasi Untuk Meningkatkan Kualitas Dan Produktivitas Padi Ud Sumber Rejeki.” : 4–6.
. Abd Wahid AA., Abdussamad S., Nasibu I.Z. “ Rancang bangun Menjalankan Teks Pada Dot Matrix 16 x 160 Berbasis Arduino Uno Dengan Pembaruan Sistem Data Menggunakan Perangkat Android Via Bluetooth” Jambura Journal Of Electrical And Electronics Engineering, Volume 2, No. 1, January 2020
. Amir, Ardi, and Muhammad Nur Faisal. 2015. “PERALATAN ELEKTRONIK JARAK JAUH BERBASIS WEB.” 6(2): 577–84.
. Cahyadi, M, Emir Nasrullah, Agus Trisanto, and A Latar Belakang. 2016. “Rancang Bangun Catu Daya DC 1V – 20V Menggunakan Kendali P-I Berbasis Mikrokontroler.” 10(2).
. Hulukati, Stephan A. 2015. “Perancangan Dan Pembuatan Miniatur Sistem Otomatis Pengering Kopra Dengan Algoritma Pid Berbasis Programmable Logic Controller ( PLC ).” Jurnal Electrichsan 2(2).
. Hulukati S.A Handayani T.P, Jaya R, Abdussamad S., (2019). “A Prototype Of Solar Powered Automatic Ablution Tap” IOP Conference Series: Materials Science And Engineering 486, 012078, (2019)
. Kanoi Yusuf H, Abdussamad S, Dali S, Wahyuni., (2019). “Perancangan Jam Digital Waktu Sholat Menggunakan Arduino Uno” Jambura Journal Of Electrical And Electronics Engineering Volume 1 No. 2 Juli 2019
. Mandala, Harmanda et al. 2015. “Perancangan Sistem Otomatisasi Penggilingan Teh Hitam Orthodoks Menggunakan Pengendali PLC Siemens S7 1200 Dan Supervisory Control and Data Acquisition ( SCADA ) Di PT . Perkebunan Nusantara VIII Rancabali.” 2(1).
. Manggalla, Lukas Kano. 2008. “Perancangan Pengering Gabah Menggunakan Pemanas Udara Dari Tungku Sekam.” Metropolar 6(1): 10–15.
. Stephanus Antonius Ananda, and Edhi Tanaka Soewangsa. 2003. “Studi Karateristik Motor DC Penguat Luar Terhadap Posisi Sikat.” Jurnal Teknik Elektro 3(1): 51–56. http://puslit2.petra.ac.id/ejournal/index.php/elk/article/view/15869.
. Suprapti, Niken, and Agus Purwanto. 2013. “Sistem Kontrol Pengaduk Pada Alat Pengering Gabah.” Fisika 6(1): 30–38.
. S. Abdussamad, “Rancang Bangun Inverter Mini 1.5 Vdc to 220 Vac Untuk Lampu Darurat,” J. Tek., vol. 18, no. 1, pp. 7–16, Jun. 2020.
. Wirajaya M. Rizky., Abdussamad S., Nasibu I. Z., “Rancang Bangun Mesin Penetas Telur Otomatis Menggunakan Mikrokontroler Arduino Uno” Jambura Journal Of Electrical And Electronics Engineering, Volume 2, No. 1, Januari 2020